It can be tough switching between your 6-over-6 Yagi, your 4
element Quad, your 600' terminated Rhombic, and your full-size 160
meter vertical. I know I just hate it; spelunking under the desk,
wrangling stiff pigtails of RG-8 up to the rig. Even if you use a
coax switch, most of them have the connectors splayed out at all
angles, leaving the coax running all over the place, taking up half
the desk. And then, you have to be able to reach the switch knob, so
all that RG-8 is right there in your face.
So you get all that sorted out, you're at your local ham club
meeting one evening when a killer lighting storms sweeps through,
and you find yourself wondering if you remembered to set the switch
to ground your antennas. If not, you may be treated to a smoking
heap of rubble where your favorite rig used to be when you get home.
Well, help is at hand. The LDG DTS-4 Desktop Coaxial Switch is made
for hams, by hams, to solve these very problems. With the DTS-4 you
can instantly switch your rig between 4 antennas with the press of a
button. All five coax sockets (4 inputs and one output to your rig)
are lined up across the back of the switch, so all the coax can run
straight back. This means the DTS-4 will fit in just about anywhere
on your operating desk. A bright red LED indicates the antenna in
use. At a touch of the control buttons, all inputs are grounded,
helping to protect your radio from Mother Nature.
Remember that lightning storm? The DTS-4 can sense when your rig is
turned off, and automatically ground all antenna inputs! You simply
run a line from a DC-out port on your rig (most modern rigs have at
least one) to the DTS-4 and set it to Radio Sense mode with a simple
button-press. From then on you're protected; when you turn your rig
off everything is automatically grounded. When you power back up,
the DTS-4 automatically resets to the antenna you were last using.
Use your radio’s auto power off feature and it will even protect you
if you forget!
But that's just the beginning! How about remote-mounting the DTS-4,
say on the floor under the desk, or even in the basement to keep all
that pesky coax at bay, and using a compact remote control box on
your operating desk?
The DTS-4R remote control fills the bill, with a full set of control
buttons and indicator lights, but only a single, slim control cable
running to the remote DTS-4 switch.
The DTS-4 handles up to 1500 watts of RF power on HF (1000W on 6M),
and can be used with any coax-fed antenna. The Radio Sense feature
needs at least 2 volts from your rig, at 1 mA current. The DTS-4
features Teflon SO-239 connectors, and requires an external 12 vdc
power supply at 250 ma. If the external power supply fails, all
inputs are grounded, so it's fail-safe. Switching is done by rugged,
sealed industrial relays.
Add the DTS-4 and DTS-4R to your shack soon; it's the modern coax
switch you've been waiting for.
|
| Specifications |
 |
Six position coaxial antenna switch.
|
|
Safety features prevent “hot switching”.
|
|
Radio sense (when used with remote) allows
auto-off control to ground all positions.
|
|
Frequency range: 1.8 – 54 MHz
|
|
Power requirements: 11 – 15 volts DC at 100 mA
maximum |
|
Idle current (all grounded): 10 mA. |
|
Serial Interface: TTL 2400 baud 8-N-1. |
|
Switch Size: 9.5” wide x 4.5” deep x 2” high
|
|
Remote Size: 6” wide x 3” deep x 2” high
|
|
Weight: 1 lb. |
|
|
